DOSERAY

STORAGE – DOSING – CONVEYING

Sultan Makina Ltd. Şti.

+90 226 353 21 21

Pneumatic Conveying Systems

 dense phase conveying 2dense phase conveying
Dense Phase Pneumatic Conveying
Among air conveying systems, dense phase conveying is used especially for abrasive and difficult-to-convey materials. The sand, cement and glass industries are typical examples.
Because the material is abrasive, it must not strike the pipe wall at high speed; at high pressures such as 2–5 bar, the air-material mixture fills the pipe as it moves and is conveyed over long distances. Bulk cement tankers, for example, work on this principle. Instead of the high-volume fans used in dilute phase, this method uses high-capacity screw compressors and dryers.


In this method, high-pressure air is introduced into a pressure vessel filled with the solid material to be conveyed; a valve then opens and the air-material mixture is transferred to a cyclone, silo or target mixer. This method is preferred especially for materials that may form fibres or whose characteristics may be degraded by friction during conveying. By its nature, dense phase conveying works with different instruments from dilute phase, and its equipment is more robust. This high-pressure conveying uses thick-walled pipes and special basalt-lined bends.

The centrifugal or Roots-type blowers used as air generators in pneumatic conveying draw in ambient air and compress it to create a conveying pressure. Water droplets originating from the relative humidity of the atmospheric air act as a good conductor during compression and cause the conveying air to heat up. Depending on the operating pressure and conveying speed of the process, this temperature can at times reach 80 °C.
If the material to be conveyed is affected by such temperatures, pre-cooling and after-cooling of the compressed air may be required before it enters the process. In terms of air temperature, air velocity and required capacity, a dense phase transporter (pressure vessel conveyor) may be the most suitable solution instead of a complex dilute phase system.
Dilute and Medium Phase Pneumatic Conveying
rotary valvepneumatic conveying

Vacuum Conveyors
vacuum transport vacuum conveying

In dilute phase, pneumatic conveying can be done either under vacuum or under pressure. Conveying with negative pressure is called vacuum conveying or a vacuum conveyor. The most important point when conveying product under vacuum is to ensure that the system can take in air. The best example of the vacuum method is a vacuum cleaner. Vacuum conveying systems usually operate at a maximum of -500 mbar. The products conveyed most efficiently are those in grain or granular form. For powder products, a filter is used to separate the product from the air. In vacuum conveying, the filter area needs to be larger than in pressure conveying; in short, the vacuum conveyor method puts an extra load on the filters.

Besides blowers, vacuum pumps or high-pressure compressed air can also be used as the air suction system.

Mechanical Conveying
  screw manufacturing
Although mechanical conveying may seem difficult and has some limitations, it is the most economical solution in terms of power consumption. Over long distances the investment cost is high, but power consumption is low. In pneumatic conveying applications it is also generally used for volumetric feeding at a constant rate.

Pneumatic conveying, on the other hand, is the most flexible conveying method compared with screw, belt and chain conveyors. Although it has to work together with many auxiliary instruments and dust collection systems, its flexibility makes it the most widely preferred conveying system.

In pneumatic conveying processes, every product conveyed by air is first mixed with the air and then separated from it. Although both steps are difficult, the method is always preferred because of its flexibility.

Mixing is done with rotary valves (airlocks), loading stations and venturis, while separation is done with filters. In short, pneumatic conveying means dust; it means separating the dust and always filtering it.

Blowers, i.e. low-pressure, high-volume fans, are used as the air source in pneumatic conveying.
Although the process looks like a simple system in which the product is mixed with compressed air and conveyed, it requires serious engineering and experience. Pressure and vacuum can also be combined in pneumatic conveying processes.

Every product to be conveyed pneumatically has different characteristics. Each product therefore has a different density and optimum conveying pressure, which changes the way it is conveyed. If you try to convey sugar on a line built for flour without making any changes, the process can be expected to fail; none of the equipment you use will work properly. If the process is designed correctly and built with the right instruments and equipment, you can convey both sugar and flour on the same line simply by changing parameters in the automation. This example shows how important a sound infrastructure and experience are in practice.

Tags: pneumatic conveying, dense phase conveying, silo discharge systems, airlock, rotary valve, screw conveyor, vacuum pneumatic conveying, vacuum product conveying, vacuum conveying, vacuum conveyor, air conveying systems, pneumatic powder conveying systems, air conveying applications, air conveying and dosing systems