Where Is Micro Dosing Used?
Micro dosing systems are custom-built to meet the needs of pharmaceutical, chemical, food and other industrial plants that produce to recipes. They are produced in various diameters, pitches and types to suit each plant's requirements. Depending on the process, their accuracy ranges from 1 to 30 g. This accuracy is directly related to the granular structure of the raw materials being dosed and the operating time.
Micro dosing screws fall into two groups depending on the material passing through them:
1. Single screw
2. Twin screw with two barrels
Single-screw feeders allow more precise weighing by varying the frequency with an inverter, but they extend the batch time. This approach is common in small plants, with long batch times and in single-component dosing systems. For short batch times and multi-component dosing systems, twin-screw feeders should be preferred, so that the raw materials making up the batch are dosed in less time.
The choice of micro dosing system depends not only on the feeder (dosing screw) but also on how the process runs. For example, the product or products to be dosed can be weighed in a single hopper and then fed into the process. In other words, weighing can be performed on the loss-in-weight principle with a dosing screw attached to the hopper.
Weighing and Dosing Methods
1. Loss-in-weight principle
2. Gain-in-weight principle
A loss-in-weight unit works as follows: a hopper filled with material sits on load cells. Beneath the hopper is a single or twin screw feeder, attached to the hopper frame and included in the tare. Depending on the process, the feeder may also be a vibrating conveyor, an air slide or a rotary valve. The load cell signals and the screw feeder control are connected to the PLC.
The PLC software runs the screw feeder fast or slow according to the set quantity. The dosed quantity is calculated from the decrease in weight in the hopper.
In dosing systems working on the loss-in-weight principle, each feeder must have its own load cell system. Dosing can be performed with a screw, a gate valve or a rotary valve.
In systems where weighing takes place in a single hopper, weighing the hopper alone is sufficient. Taring in this process gives an accurate result more quickly.
Selecting the right dosing system is the responsibility of the process designer, and the properties of the raw material must always be taken into account in that choice.
The flight geometry of the conveying screws in micro dosing units can vary; as explained, this difference relates to the pitch at the same diameter.
Micro-Dosing and Custom Builds
In micro dosing processes, the pitch increases or decreases the speed and tolerance of the screw feeder. A single micro dosing unit can use more than one screw to handle different materials. Even with the same feed tube, the operating regime changes as the conveyed material changes, and tolerances may differ. For example, a powder may be dosed with a tolerance of 1 mm, while a granule can be dosed with a tolerance of 2 mm on the same unit by changing the screw.
Remember also that dosing can be performed not only with a screw but also with a rotary valve or a gate valve.
Although this information may seem encyclopaedic, it is intended as background to help you design your processes more accurately. Understanding how the system works makes it easier to reach the right result.
- Micro-Dosing Screws
Main Advantages of Micro Dosing Systems
· Minimum Waste and Cost Savings: Optimises raw material costs by preventing overuse of expensive ingredients.
· Consistent Quality: Eliminates manual weighing errors caused by human factors.
· Occupational Safety and Hygiene: Provides a safe working environment by transferring chemical or powdered materials in closed systems.
Precision Weighing with Micro Dosing
In the dosing processes we build, the goal is to operate with minimum fluctuation. In load cell-based dosing, depending on the process, 1 to 4 feeders can discharge into a single hopper on load cells. When several screws feed one hopper, the load on the hopper may vary depending on where the screws enter it. Fine details like these are at the heart of a micro dosing process.
READ MORE